Physics-
General
Easy
Question
A milliammeter of range 10 mA and resistance 9 
is joined in a circuit as shown. The metre gives full-scale deflection for current I when A and B are used as its terminals, i.e., current enters at A and leaves at B (C is left isolated). The value of I is
- 100 mA
- 900 mA
- 1 A
- 1.1 A
The correct answer is: 1 A
Related Questions to study
physics-
In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 resistor. The galvanometer resistance is
In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 resistor. The galvanometer resistance is
physics-General
physics-
The variation of current (I) and voltage (V) is as shown in figure A. The variation of power P with current I is best shown by which of the following graph
The variation of current (I) and voltage (V) is as shown in figure A. The variation of power P with current I is best shown by which of the following graph
physics-General
physics-
What amount of heat will be generated in a coil of resistance R due to a charge q passing through it if the current in the coil decreases to zero uniformly during a time interval 
What amount of heat will be generated in a coil of resistance R due to a charge q passing through it if the current in the coil decreases to zero uniformly during a time interval
physics-General
physics-
In the circuit shown, the resistances are given in ohms and the battery is assumed ideal with emf equal to 3.0 volts. The resistor that dissipates the most power is
In the circuit shown, the resistances are given in ohms and the battery is assumed ideal with emf equal to 3.0 volts. The resistor that dissipates the most power is
physics-General
physics-
In the figure shown the power generated in y is maximum when y = 5. Then R is
In the figure shown the power generated in y is maximum when y = 5. Then R is
physics-General
physics-
The ratio of powers dissipatted respectively in R and 3R, as shown is:
The ratio of powers dissipatted respectively in R and 3R, as shown is:
physics-General
physics-
In the circuit shown the cells are ideal and of equal emfs, the capacitance of the capacitor is C and the resistance of the resistor is R. X is first joined to Y and then to Z. After a long time, the total heat produced in the resistor will be
In the circuit shown the cells are ideal and of equal emfs, the capacitance of the capacitor is C and the resistance of the resistor is R. X is first joined to Y and then to Z. After a long time, the total heat produced in the resistor will be
physics-General
physics-
A total charge Q flows across a resistor R during a time interval = T in such a way that the current vs. time graph for 
is like the loop of a sin curve in the range 
. The total heat generated in the resistor is
A total charge Q flows across a resistor R during a time interval = T in such a way that the current vs. time graph for is like the loop of a sin curve in the range . The total heat generated in the resistor is
physics-General
physics-
In the diagram resistance between any two junctions is R. Equivalent resistance across terminals A and B is
In the diagram resistance between any two junctions is R. Equivalent resistance across terminals A and B is
physics-General
physics-
In the circuit shown in figure reading of voltmeter is V1 when only S1 is closed, reading of voltmeter is V2 when only S2 is closed. The reading of voltmeter is V3 when both S1 and S2 are closed then
In the circuit shown in figure reading of voltmeter is V1 when only S1 is closed, reading of voltmeter is V2 when only S2 is closed. The reading of voltmeter is V3 when both S1 and S2 are closed then
physics-General
physics-
In the circuit shown, what is the potential difference VPQ?
In the circuit shown, what is the potential difference VPQ?
physics-General
physics-
The circuit diagram shown consists of a large number of element (each element has two resistors R1 and R2). The resistance of the resistors in each subsequent element differs by a factor of K = 1/2 from the resistance of the resistors in the previous elements. The equivalent reistance between A and B shown in figure is :
The circuit diagram shown consists of a large number of element (each element has two resistors R1 and R2). The resistance of the resistors in each subsequent element differs by a factor of K = 1/2 from the resistance of the resistors in the previous elements. The equivalent reistance between A and B shown in figure is :
physics-General
physics-
In the given circuit the current flowing through the resistance 20 ohms is 0.3 ampere while the ammeter reads 0.8 ampere. What is the value of R1?
In the given circuit the current flowing through the resistance 20 ohms is 0.3 ampere while the ammeter reads 0.8 ampere. What is the value of R1?
physics-General
physics-
ABCD is a square where each side is a uniform wire of resistance 1. A point E lies on CD such that if a uniform wire of resistance 1 is connected across AE and constant potential difference is applied across A and C then B and E are equipotential.
ABCD is a square where each side is a uniform wire of resistance 1. A point E lies on CD such that if a uniform wire of resistance 1 is connected across AE and constant potential difference is applied across A and C then B and E are equipotential.
physics-General
physics-
Consider an infinte ladder network shown in figure. A voltage V is applied between the points A and B. This applied value of voltage is halved after each section.
Consider an infinte ladder network shown in figure. A voltage V is applied between the points A and B. This applied value of voltage is halved after each section.
physics-General
