Physics-
General
Easy
Question
A plank with a uniform sphere placed on it rests on a smooth horizontal plane. Plank is pulled to right by a constant force F. If sphere does not slip over the plank. Which of the following is incorrect.
- Acceleration of the centre of sphere is less than that of the plank.
- Work done by friction acting on the sphere is equal to its total kinetic energy.
- Total kinetic energy of the system is equal to work done by the force F
- None of the above
The correct answer is: Total kinetic energy of the system is equal to work done by the force F
Related Questions to study
Physics-
A plank of mass M is placed over smooth inclined plane and a sphere is also placed over the plank. Friction is sufficient between sphere and plank. If plank and sphere are released from rest, the frictional force on sphere is:
A plank of mass M is placed over smooth inclined plane and a sphere is also placed over the plank. Friction is sufficient between sphere and plank. If plank and sphere are released from rest, the frictional force on sphere is:
Physics-General
Physics-
A disc of radius r is rotating about its centre with an angular speed 
. It is gently placed on a rough horizontal surface. After what time it will be in pure rolling ?
A disc of radius r is rotating about its centre with an angular speed . It is gently placed on a rough horizontal surface. After what time it will be in pure rolling ?
Physics-General
Physics-
Portion AB of the wedge shown in figure is rough and BC is smooth. A solid cylinder rolls without slipping from A to B. The ratio of translational kinetic energy to rotational kinetic energy, when the cylinder reaches point C is :
Portion AB of the wedge shown in figure is rough and BC is smooth. A solid cylinder rolls without slipping from A to B. The ratio of translational kinetic energy to rotational kinetic energy, when the cylinder reaches point C is :
Physics-General
Physics-
Inner and outer radii of a spool are r and R respectively. A thread is wound over its inner surface and placed over a rough horizontal surface. Thread is pulled by a force F as shown in fig. then in case of pure rolling
Inner and outer radii of a spool are r and R respectively. A thread is wound over its inner surface and placed over a rough horizontal surface. Thread is pulled by a force F as shown in fig. then in case of pure rolling
Physics-General
Physics-
A disc of radius R is rolling purely on a flat horizontal surface, with a constant angular velocity. The angle between the velocity and acceleration vectors of point P is
A disc of radius R is rolling purely on a flat horizontal surface, with a constant angular velocity. The angle between the velocity and acceleration vectors of point P is
Physics-General
Physics-
Two points of a rigid body are moving as shown. The angular velocity of the body is:
Two points of a rigid body are moving as shown. The angular velocity of the body is:
Physics-General
Physics-
A hinged construction consists of three rhombs with the ratio of sides 5:3:2. Vertex A3 moves in the horizontal direction at a velocity v. Velocity of A2 is
A hinged construction consists of three rhombs with the ratio of sides 5:3:2. Vertex A3 moves in the horizontal direction at a velocity v. Velocity of A2 is
Physics-General
Physics-
A particle starts from the point (0m, 8m) and moves with uniform velocity of 
After 5 seconds, the angular velocity of the particle about the origin will be :
A particle starts from the point (0m, 8m) and moves with uniform velocity of After 5 seconds, the angular velocity of the particle about the origin will be :
Physics-General
Physics-
A uniform rod is fixed to a rotating turntable so that its lower end is on the axis of the turntable and it makes an angle of 20° to the vertical. (The rod is thus rotating with uniform angular velocity about a vertical axis passing through one end.) If the turntable is rotating clockwise as seen from above.
Is there a torque acting on it, and if so in what direction?
A uniform rod is fixed to a rotating turntable so that its lower end is on the axis of the turntable and it makes an angle of 20° to the vertical. (The rod is thus rotating with uniform angular velocity about a vertical axis passing through one end.) If the turntable is rotating clockwise as seen from above.
Is there a torque acting on it, and if so in what direction?
Physics-General
Physics-
A uniform rod is fixed to a rotating turntable so that its lower end is on the axis of the turntable and it makes an angle of 20° to the vertical. (The rod is thus rotating with uniform angular velocity about a vertical axis passing through one end.) If the turntable is rotating clockwise as seen from above.
What is the direction of the rod's angular momentum vector (calculated about its lower end)?
A uniform rod is fixed to a rotating turntable so that its lower end is on the axis of the turntable and it makes an angle of 20° to the vertical. (The rod is thus rotating with uniform angular velocity about a vertical axis passing through one end.) If the turntable is rotating clockwise as seen from above.
What is the direction of the rod's angular momentum vector (calculated about its lower end)?
Physics-General
Physics-
A child with mass m is standing at the edge of a disc with moment of inertia I, radius R, and initial angular velocity 
. See figure given below. The child jumps off the edge of the disc with tangential velocity v with respect to the ground. The new angular velocity of the disc is
A child with mass m is standing at the edge of a disc with moment of inertia I, radius R, and initial angular velocity . See figure given below. The child jumps off the edge of the disc with tangential velocity v with respect to the ground. The new angular velocity of the disc is
Physics-General
Physics-
A man is sitting in a smooth groove on a horizontal circular table at the edge by holding a rope joined to the centre. The moment of inertia of table is I. Mass of man = M. Man now pulls the rope so that he comes to the centre. The angular velocity of the table :
A man is sitting in a smooth groove on a horizontal circular table at the edge by holding a rope joined to the centre. The moment of inertia of table is I. Mass of man = M. Man now pulls the rope so that he comes to the centre. The angular velocity of the table :
Physics-General
Physics-
A small bead of mass m moving with velocity v gets threaded on a stationary semicircular ring of mass m and radius R kept on a horizontal table. The ring can freely rotate about its centre. The bead comes to rest relative to the ring. What will be the final angular velocity of the system?
A small bead of mass m moving with velocity v gets threaded on a stationary semicircular ring of mass m and radius R kept on a horizontal table. The ring can freely rotate about its centre. The bead comes to rest relative to the ring. What will be the final angular velocity of the system?
Physics-General
Physics-
A block of mass m is attached to a pulley disc of equal mass m, radius r by means of a slack string as shown. The pulley is hinged about its centre on a horizontal table and the block is projected with an initial velocity of 5 m/s. Its velocity when the string becomes taut will be
A block of mass m is attached to a pulley disc of equal mass m, radius r by means of a slack string as shown. The pulley is hinged about its centre on a horizontal table and the block is projected with an initial velocity of 5 m/s. Its velocity when the string becomes taut will be
Physics-General
Physics-
A solid cone hangs from a frictionless pivot at the origin O, as shown. If 
and
are unit vectors, and a, b, and c are positive constants, which of the following forces F applied to the rim of the cone at a point P results in a torque t on the cone with a negative component t Z ?
A solid cone hangs from a frictionless pivot at the origin O, as shown. If and are unit vectors, and a, b, and c are positive constants, which of the following forces F applied to the rim of the cone at a point P results in a torque t on the cone with a negative component t Z ?
Physics-General
