Question
pitch of screw gauge is 1 mm and there are 100 divisions on the circular scak. What measurin the diametcr of a wire, the linear scale reads, 1 mm and 47t division on the circular scale coincide with the reference line. The lengthof the wire 155.6 cm. What will be the curved surface area (in cm2 of the wire in appropriate number of significant figures.
- 2.6 cm2
- 2.5848 cm2
- 2.585 cm2
- 2.5 cm2
The correct answer is: 2.6 cm2
Related Questions to study
The nucleus 
after two successive 
decays will give
The nucleus after two successive decays will give
The screw gauges shown above has a zero error of -0.02 and 100 divisions on the circular scak What is the diameter of wire?
The screw gauges shown above has a zero error of -0.02 and 100 divisions on the circular scak What is the diameter of wire?
The number of ways of dividing 52 cards amongst four players equally, are
The number of ways of dividing 52 cards amongst four players equally, are
The half-life of radioactive Radon is 3.8 days. The time at the end of which (1/20)th of the Radon sample will remain undecayed is (given 
The half-life of radioactive Radon is 3.8 days. The time at the end of which (1/20)th of the Radon sample will remain undecayed is (given
Screw gauge A has a pitch of and 50 division on its circular scale screw guage B has a pitc of 0.5 and 100 divisions on its circular scale. If is least count, then which
posibility i true ? What is the parilrility
Screw gauge A has a pitch of and 50 division on its circular scale screw guage B has a pitc of 0.5 and 100 divisions on its circular scale. If is least count, then which posibility i true ? What is the parilrility
the screw and stud touch each other, the edge of a certain screw gauge is to the right of the C mark on the main scale and 5th division of the circular scale coincides with the line of graduation then what is the value of zero error ?
the screw and stud touch each other, the edge of a certain screw gauge is to the right of the C mark on the main scale and 5th division of the circular scale coincides with the line of graduation then what is the value of zero error ?
A radioactive sample has N0 active atoms t = 0. If the rate of disintegration at any time is R and the number of atoms is N, then the ratio R/N varies with time as
A radioactive sample has N0 active atoms t = 0. If the rate of disintegration at any time is R and the number of atoms is N, then the ratio R/N varies with time as
When the screw and stud touch each other, the edges of a certain screw gauge is on left of the mark on the main scale and the 96th division of the circular scale coincides with the circular line graduation then what is the value of zero error
When the screw and stud touch each other, the edges of a certain screw gauge is on left of the mark on the main scale and the 96th division of the circular scale coincides with the circular line graduation then what is the value of zero error
Consider the arrangement of three metal plates A, B, and C of equal surface area and separation d as shown in figure. The energy stored in the arrangement, when the plates are fully charged, is
Consider the arrangement of three metal plates A, B, and C of equal surface area and separation d as shown in figure. The energy stored in the arrangement, when the plates are fully charged, is
the edge of the circular scale lies to the right of the 0 mark on the main scale, when the stu and the spindle touch each other, then what will be the zero error?
the edge of the circular scale lies to the right of the 0 mark on the main scale, when the stu and the spindle touch each other, then what will be the zero error?
The reaction
, is called
The reaction, is called
done in carrying a charge Q1 once round a circle of radius R with a charge Q2 at the centre I Is
done in carrying a charge Q1 once round a circle of radius R with a charge Q2 at the centre I Is
when the edge of the circular scale lies to the left of 0 mark on the main scale, when the stud an spindle touch each other, Then what will be the zero error?
when the edge of the circular scale lies to the left of 0 mark on the main scale, when the stud an spindle touch each other, Then what will be the zero error?
Ethyl ester 
, the product ‘P’ will be
Ethyl ester , the product ‘P’ will be
