Physics
Fluid-Mechanics
Easy
Question
A cylindrical vessel is filled with water upto the height 1 m from the base. A small orifice is opened at some height in the cylinder and the water level is reduced to height of orifice in 20 sec. If the base area of the cylinder is 100 times the area of orifice, then the height of orifice from the base is (Take 
)
- 80 cm
- 60 cm
- 40 cm
- 20 cm
The correct answer is: 60 cm
Related Questions to study
Physics
Consider a vessel filled with a liquid upto height H. The bottom of the vessel lies in the X-Y plane passing through the or origin. The density of the liquid varies with Z-axis as
are the pressures at the bottom surface and top surface of the liquid, the magnitude of 
is:
Consider a vessel filled with a liquid upto height H. The bottom of the vessel lies in the X-Y plane passing through the or origin. The density of the liquid varies with Z-axis as
are the pressures at the bottom surface and top surface of the liquid, the magnitude of is:
PhysicsFluid-Mechanics
Physics
A tank of height 15 m and cross-section area 10 m2 is filled with water. There is a small hole of cross-section area ' a ' which is much smaller than the container, located at a height of 12m from the base of the container. How much force should be applied with a piston at the top level, so that the water coming out of the hole hits the ground at a distance of 16 m. (Take density of water =1000 kg / m3)
A tank of height 15 m and cross-section area 10 m2 is filled with water. There is a small hole of cross-section area ' a ' which is much smaller than the container, located at a height of 12m from the base of the container. How much force should be applied with a piston at the top level, so that the water coming out of the hole hits the ground at a distance of 16 m. (Take density of water =1000 kg / m3)
PhysicsFluid-Mechanics
Physics
Water flows through a pipe as shown in the figure. The areas of cross-section of sections A and B respectively are 4 cm2 and 1 cm2. The gauge pressure in the pipe at the centre of section A is and the flow rate is 
and the flow rate is 800 cm3 s-1 . The difference in heights of the water levels in the vertical pipes is m. (Acceleration due to gravity =10 ms-2)
Water flows through a pipe as shown in the figure. The areas of cross-section of sections A and B respectively are 4 cm2 and 1 cm2. The gauge pressure in the pipe at the centre of section A is and the flow rate is and the flow rate is 800 cm3 s-1 . The difference in heights of the water levels in the vertical pipes is m. (Acceleration due to gravity =10 ms-2)
PhysicsFluid-Mechanics
Physics
A liquid flows along a horizontal pipe AB of uniform cross section The difference between the levels of the liquid in tubes P and Q is 10 am. The diameters of the tubes P and Q are the same. Then 
A liquid flows along a horizontal pipe AB of uniform cross section The difference between the levels of the liquid in tubes P and Q is 10 am. The diameters of the tubes P and Q are the same. Then
PhysicsFluid-Mechanics
Physics
Water of density flows out of a big tank along a tube bent at right angles. Length of the horizontal section of the tube is equal to L. Flow rate of water is Q. Torque due to the reaction of flowing water acting on the tube's walls radiative to point P will be (A is area of cross section of tube).
Water of density flows out of a big tank along a tube bent at right angles. Length of the horizontal section of the tube is equal to L. Flow rate of water is Q. Torque due to the reaction of flowing water acting on the tube's walls radiative to point P will be (A is area of cross section of tube).
PhysicsFluid-Mechanics
Physics
In the given management density of block A is 2d and density of liquid is d. The system is released from rest such that block B moves up in liquid with an acceleration a1 and moves down with an acceleration a1 and moves down with an acceleration a2 when it is outside the liquid. If a1=a2, ratio of masses of blocks A and B will be
In the given management density of block A is 2d and density of liquid is d. The system is released from rest such that block B moves up in liquid with an acceleration a1 and moves down with an acceleration a1 and moves down with an acceleration a2 when it is outside the liquid. If a1=a2, ratio of masses of blocks A and B will be
PhysicsFluid-Mechanics
Physics
A light cone is in equilibrium under the action of hydrostatic forces of two liquids of densities 
A light cone is in equilibrium under the action of hydrostatic forces of two liquids of densities
PhysicsFluid-Mechanics
Physics
Two cylinders of same area of cross section and together to form a cylinder of length L but made of two materials of densities d1 and d2 are connected together to from a cylinder of length 2L. The combination floats in a liquid of density d with a length L/2 above the surface of the liquid, If 
and difference in densities of two cylinders is equal to density of the liquid
Two cylinders of same area of cross section and together to form a cylinder of length L but made of two materials of densities d1 and d2 are connected together to from a cylinder of length 2L. The combination floats in a liquid of density d with a length L/2 above the surface of the liquid, If and difference in densities of two cylinders is equal to density of the liquid
PhysicsFluid-Mechanics
Physics
A cone of height h, radius r and density d1 is floating in a liquid of density d12. If depth of immersion of cone is y and 
A cone of height h, radius r and density d1 is floating in a liquid of density d12. If depth of immersion of cone is y and
PhysicsFluid-Mechanics
Physics
Two immiscible liquids of densities d and 2d with heights h and 2h respectively push a vertical plate as shown. If b is width of the plate, total side thrust given by liquids on the vertical plate will be
Two immiscible liquids of densities d and 2d with heights h and 2h respectively push a vertical plate as shown. If b is width of the plate, total side thrust given by liquids on the vertical plate will be
PhysicsFluid-Mechanics
Physics
A spherical tank of radius R is half filled with oil of density d. If the tank is given a horizontal. Acceleration of a, maximum pressure on the tank is (due to liquid alone or pressure above liquid =0)
A spherical tank of radius R is half filled with oil of density d. If the tank is given a horizontal. Acceleration of a, maximum pressure on the tank is (due to liquid alone or pressure above liquid =0)
PhysicsFluid-Mechanics
Physics
A drop of liquid of diameter 2.8 mm breaks up into 125 identical drops. The change in energy is nearly (S.T. of liquid =75 dynes/cm)
A drop of liquid of diameter 2.8 mm breaks up into 125 identical drops. The change in energy is nearly (S.T. of liquid =75 dynes/cm)
PhysicsFluid-Mechanics
Physics
Two droplets merge with each other and forms a large droplet. In this process
Two droplets merge with each other and forms a large droplet. In this process
PhysicsFluid-Mechanics
Physics
The potential energy of a molecule on the surface of liquid compared to one inside the liquid is
The potential energy of a molecule on the surface of liquid compared to one inside the liquid is
PhysicsFluid-Mechanics
Physics
Energy needed in breaking a drop of radius R into n drops of radii r is given by
Energy needed in breaking a drop of radius R into n drops of radii r is given by
PhysicsFluid-Mechanics
