Physics-
General
Easy
Question
A uniform cylinder rests on a cart as shown. The coefficient of static friction between the cylinder and the cart is 0.5. If the cylinder is 4 cm in diameter and 10 cm in height, which of the following is the minimum acceleration of the cart needed to cause the cylinder to tip over?
- 2 m/s2
- 4 m/s2
- 5 m/s2
- the cylinder would slide before it begins to tip over.
The correct answer is: 4 m/s2
Related Questions to study
physics-
A uniform ladder of length 5m is placed against the wall as shown in the figure. If coefficient of friction m is the same for both the walls, what is the minimum value of 
for it not to slip?
A uniform ladder of length 5m is placed against the wall as shown in the figure. If coefficient of friction m is the same for both the walls, what is the minimum value of for it not to slip?
physics-General
physics-
A smooth rod of length 
is kept inside a trolley at an angle 
as shown in the figure. What should be the acceleration a of the trolley so that the rod remains in equilibrium with respect to it?
A smooth rod of length is kept inside a trolley at an angle as shown in the figure. What should be the acceleration a of the trolley so that the rod remains in equilibrium with respect to it?
physics-General
physics-
Find minimum height of obstacle so that the sphere can stay in equilibrium.
Find minimum height of obstacle so that the sphere can stay in equilibrium.
physics-General
physics-
A homogeneous cubical brick lies motionless on a rough inclined surface. The half of the brick which applies greater pressure on the plane is :
A homogeneous cubical brick lies motionless on a rough inclined surface. The half of the brick which applies greater pressure on the plane is :
physics-General
physics-
A uniform cube of side ‘b’ and mass M rest on a rough horizontal table. A horizontal force F is applied normal to one of the face at a point, at a height 3b/4 above the base. What should be the coefficient of friction (m) between cube and table so that is will tip about an edge before it starts slipping?
A uniform cube of side ‘b’ and mass M rest on a rough horizontal table. A horizontal force F is applied normal to one of the face at a point, at a height 3b/4 above the base. What should be the coefficient of friction (m) between cube and table so that is will tip about an edge before it starts slipping?
physics-General
physics-
In an experiment with a beam balance on unknown mass m is balanced by two known mass m is balanced by two known masses of 16 kg and 4 kg as shown in figure. The value of the unknown mass m is
In an experiment with a beam balance on unknown mass m is balanced by two known mass m is balanced by two known masses of 16 kg and 4 kg as shown in figure. The value of the unknown mass m is
physics-General
physics-
A right triangular plate ABC of mass m is free to rotate in the vertical plane about a fixed horizontal axis through A. It is supported by a string such that the side AB is horizontal. The reaction at the support A is:
A right triangular plate ABC of mass m is free to rotate in the vertical plane about a fixed horizontal axis through A. It is supported by a string such that the side AB is horizontal. The reaction at the support A is:
physics-General
physics-
Two uniform rods of equal length but different masses are rigidly joined to form an L-shaped body, which is then pivoted as shown. If in equilibrium the body is in the shown configuration, ratio M/m will be:
Two uniform rods of equal length but different masses are rigidly joined to form an L-shaped body, which is then pivoted as shown. If in equilibrium the body is in the shown configuration, ratio M/m will be:
physics-General
physics-
A 5 m long pole of 3 kg mass is placed against a smooth vertical well as shown in the figure. Under equilibrium condition, if the pole makes an angle of 37° with the horizontal, the frictional force between the pole and horizontal surface is
A 5 m long pole of 3 kg mass is placed against a smooth vertical well as shown in the figure. Under equilibrium condition, if the pole makes an angle of 37° with the horizontal, the frictional force between the pole and horizontal surface is
physics-General
physics-
A man can move on a horizontal plank supported symmetrically as shown. The variation of normal reaction on support A with distance x of the man from the end of the plank is best represented by :
A man can move on a horizontal plank supported symmetrically as shown. The variation of normal reaction on support A with distance x of the man from the end of the plank is best represented by :
physics-General
physics-
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the y-axis is
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the y-axis is
physics-General
physics-
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about its base parallel to the x-axis is
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about its base parallel to the x-axis is
physics-General
Physics-
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the x-axis is
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the x-axis is
Physics-General
physics-
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the z-axis is
The figure shows an isosceles triangular plate of mass M and base L. The angle at the apex is 90°. The apex lies at the origin and the base is parallel to X–axis
The moment of inertia of the plate about the z-axis is
physics-General
physics-
The figure shows a uniform rod lying along the x-axis. The locus of all the points lying on the xy-plane, about which the moment of inertia of the rod is same as that about O is
The figure shows a uniform rod lying along the x-axis. The locus of all the points lying on the xy-plane, about which the moment of inertia of the rod is same as that about O is
physics-General
